3389-200.png
  • Instagram
  • Facebook
  • LinkedIn

NEED FINANCING FOR YOUR MACHINE? GREATAMERICA AND VORTEX SUPPLY HAVE YOU COVERED.

MPC-180 is a 100% solid, two component fast curing epoxy coating designed for controlling moisture vapor emissions on new or deteriorated concrete floors. This coating is recommended to be applied in areas of high humidity or on wet concrete. When applied at a thickness of 18 mils, it exceeds ASTM F3010 product requirements for vapor permeance. This coating will withstand moisture vapor emission rates up to 25lbs./24hrs./1000 ft2 when applied properly.

 

Areas of application

- Industrial Use - Garages; Warehouses; Airports and hangars; Processing and manufacturing plants

- Commercial Use - Shopping malls and boutiques; Hotels; Offices; Showrooms; Restaurants; Hospitals; Schools; Community centers

- ResidentialUse–Entrancesandhallways;basements;entertainmentrooms;bathrooms;kitchens and living rooms; outdoors spaces and pool outlines

 

Packaging and Recommended Thickness

MPC- 180 is offered in the following kit sizes:
- 2-gallon kit (3.78L resin (A) and 3.78L hardener (B))

- Bulk packaging also available upon request

- Recommended Film Thickness: 90-100 sq. ft. @ 18mils

 

Surface Preparation

Remove dust, dirt, grease, oil and all other contaminants with proper cleaner/degreaser. Prepare the surface mechanically as per ICRI-CSP2 profile by diamond grinding to ensure removal of laitance, curing agents and sealers. The compressive strength of a newly poured concrete substrate must be at least 25 MPA (3635 psi) after 28 days cure and at least 1.5 MPA (218 psi) tensile strength. Be careful with condensation (within 10 degrees of the dew point). All cracks, holes and irregularities must be repaired with our epoxy crack filler prior to applying the coating.

 

Mixing Instructions

The products must be conditioned between for 18°C (65°F) and 30°C (86°F) prior to application. Pre-mix each component separately for 2-3 minutes each. Open container with 1 part of component A in it, then add the 1 part of component B to it (mixing ratio 1:1). Mix the components for at least 2-3 minutes using a low-speed drill (300-450 rpm) to reduce air entrapment and to obtain a homogeneous mixture.

 

Product Application

1. Apply 1st coat of MPC-180 using a rubber squeegee and roll to obtain a uniform coating (using a fine quality 10mm roller).

Clean equipment with xylene. Once the product has hardened, it may only be removed mechanically.

 

Product Restrictions

- Not recommended for application at temperatures below 5°C/41°F or above 30°C/86°F.
- Ambient humidity of the surroundings should not exceed 85% during application and during curing

process.
- Substrate must be clean, sound and dry.
- Substrate temperature must be 3°C(5.5°F) above measured dew point.
- Humidity content of substrate must be <6% at time of application.
- Do not apply on porous surfaces where a transfer of humidity may occur during the application.
- This coating is not a replacement for a waterproofing membrane.
- This coating does not protect against areas of high hydrostatic pressure.
- Freshly applied product must be protected against moisture, condensation and water for at least 48

hours.
- Surface discoloration of product may occur when exposed to UV rays.
- Exposure during the curing stage of the coating to the by-products of propane combustion may cause discoloration (amine blushing)

 

Health and Safety

Components A and B contain toxic and corrosive ingredients. Consult the safety data sheet (S.D.S) for further information.

 

MPC-180 Vapor Moisture Barrier Fast Cure (2 gal.)

$150.00Price

Our epoxy calculator is designed to help you plan out how much product you will need before moving forward with your epoxy flooring/countertop job. Choose from our various selections of what pertains to your square footage, the type of top coat finish you desire, and as well as primer / decorative coats. Always make sure to have more material than less, as it is crucial to have it with you on the site in case of mistakes or inaccurate application. For any further questions, please do not hesitate to ask by sending a chat request or contacting our phone number: (856)-210-3278

EPOXY

CALCULATOR

© 2020 by Vortex Supply

1001 Lower Landing Rd Suite 205, Blackwood, New Jersey 08012

Phone: (856)-210-3278

Vortex Supply LLC
  • Instagram
  • Facebook
  • LinkedIn
VortexSupply.png
0